Choosing the right blasting media for vacuum blasting: hardness, grain size, surface

Choosing the right blasting media for vacuum blasting: hardness, grain size, surface

Reading Time: 7 min.

A blasting medium is the material that hits the surface during blasting and removes the layer that is meant to go. In vacuum blasting it is a granulate that is accelerated by negative pressure, extracted again immediately and reused several times in a circuit. The choice decides whether a surface comes out clean and undamaged or suffers damage.

This guide explains how blasting media differ, which granulates systeco offers for the Tornado ACS and how to choose by surface. The product pages with all the data are the blasting media overview and the blasting media table.

Blasting media by origin: plant-based, mineral, synthetic

Blasting media can be grouped by origin. Wikipedia (German) names three groups: mineral media such as ceramic and glass beads, garnet sand and all grades of corundum (aluminium oxide), plant-based media such as nutshells, and synthetic media such as plastics. Metallic media (shot, steel grit) belong to classic blasting and play no role in vacuum blasting of building surfaces.

One prohibition matters in practice: ordinary quartz sand is not permitted as a blasting medium because the fine dust can cause silicosis (German DGUV Regel 100-500). Where dust containing quartz arises, TRGS 559 also applies. In vacuum blasting, medium and removed material are extracted immediately and captured in the filter system; even so, the choice of medium remains a safety question.

Hardness and grain size: the two adjusting screws

According to systeco, the granulates differ in size and hardness. Grain size is given in micrometres: blasting glass SG 150 corresponds to a grain size of 0.15 mm, blasting glass SG 300 to 0.3 mm. As a rule of thumb, the harder and coarser the granulate, the stronger the removal and the greater the risk of damaging a sensitive substrate. Fine, softer granulates are gentler but need more time on stubborn layers.

systeco warns, for example, about the coarser Asilit AS 250: on sensitive substrates it can cause damage. Conversely, walnut shell NS 450 is so gentle that it can also be used on glass, but only with a thoroughly cleaned machine, because other granulate would damage the pane.

The systeco granulates at a glance

According to its blasting media page, systeco offers these granulates for the Tornado ACS:

  • Walnut shell NS 450 (ground walnut shell, 0.2 to 0.45 mm): mainly for polished surfaces such as marble and granite, also on glass.
  • Blasting glass SG 150 (crushed glass, 0.1 to 0.2 mm): for light, sensitive surfaces such as external thermal insulation, plaster, paint, natural stone and clinker.
  • Blasting glass SG 300 (crushed glass, 0.2 to 0.3 mm): for light, hard surfaces such as floor tiles, well-fired clinker, concrete, hardwood and granite.
  • Asilit AS 180 (silicon dioxide and aluminium oxide, 0.04 to 0.18 mm): mainly for dark surfaces such as clinker, natural stone and concrete.
  • Asilit AS 250 (silicon dioxide and aluminium oxide, 0.09 to 0.25 mm): for hard natural stone such as granite and well-fired clinker.
  • Jet Plast DP 200 (plastic, 0.1 to 0.2 mm): primarily on plastic and sensitive materials such as polished granite and aluminium.
  • Jet Plast DP 600 (plastic, 0.3 to 0.6 mm): primarily in the food industry for cleaning containers.
  • Fused alumina EK 75 (very hard special granulate, 0.04 to 0.075 mm): exclusively for engraving and roughening natural stone.

Two notes on search terms: systeco's blasting glass is crushed glass, not spherical glass beads. systeco offers corundum as fused alumina EK 75 only for engraving and roughening; the other granulates are used for cleaning.

Which granulate for which surface

The blasting media table assigns suitable granulates to each surface. The figure in the table is the correct nozzle setting in the dosing unit. Examples from the table:

  • Clinker (fired) and concrete: SG 150 (5), SG 300 (6), AS 180 (5), AS 250 (6).
  • External insulation plaster and paint: SG 150 (5).
  • Exposed aggregate concrete: SG 150 (5) and AS 180 (5).
  • Granite, polished: NS 450 (6), DP 200 (5) and EK 75 (3).
  • Stainless steel and aluminium: AS 180 (4).
  • Softwood: SG 150 (5) and AS 180 (4).

systeco itself names typical assignments by task: SG 150 for removing graffiti (see the graffiti removal machine), AS 180 for soot removal (see soot after a fire in commercial buildings), SG 300 for removing floor markings (see removal of floor markings) and EK 75 for engraving on granite.

How to choose, step by step

  1. Identify the surface. Note the material, its colour (light or dark) and its condition.
  2. Judge the sensitivity. The more sensitive the surface, the finer and softer the granulate.
  3. Check the blasting media table. Read off the suitable granulates and the figure for the nozzle setting.
  4. Set the nozzle. Match the nozzle setting to the granulate, not the other way round.
  5. Test on an inconspicuous spot. Only when the result is right, work the whole area.
  6. Mind the task. Cleaning, roughening, engraving and polishing call for different granulates; roughening and engraving natural stone is the job of fused alumina EK 75.

Circuit and economy

According to systeco, it only offers high-quality granulates because they are reused up to 100 times in the circuit. This lowers material consumption and the amount that has to be disposed of; the removed residues stay in the machine's closed circuit until the end of the work. For orders of magnitude, systeco states an area performance for the granulates: 40 to 50 square metres for NS 450, 40 to 60 for SG 150, SG 300, AS 180 and AS 250, 30 to 40 for the Jet Plast granulates and 10 to 20 for fused alumina EK 75. A standard container of blasting glass SG 150 holds about 8 kilograms. The overview of vacuum blasting puts the overall costs into context.

Typical mistakes

  • Too hard or too coarse. AS 250 on sensitive substrates can cause damage; when in doubt, test the finer granulate first on an inconspicuous spot.
  • Wrong nozzle setting. Each granulate has its own nozzle setting. It sits in the lower container at the lower end of the funnel in the dosing unit; by lifting the plate briefly and turning it, the correct nozzle is set.
  • Mixing granulates. Especially on glass: walnut shell only with a thoroughly cleaned machine, otherwise residues of other granulates can damage the pane.
  • Quartz sand as a substitute. It is not permitted as a blasting medium; for vacuum blasting with the Tornado ACS the granulates from the overview above apply.

Anyone who wants to clarify the right granulate for a specific property can get advice via the contact page. The system behind it is described on the page about the Tornado ACS; the difference from other methods is explained in the alternative to dry ice blasting.

FAQ: Blasting media in vacuum blasting

What is a blasting medium?

A blasting medium is the material that hits the surface during blasting and removes dirt or coatings. In vacuum blasting it is a granulate that is accelerated by negative pressure and extracted again immediately.

Which blasting media does systeco offer for the Tornado ACS?

Walnut shell NS 450, blasting glass SG 150 and SG 300, Asilit AS 180 and AS 250, the plastic granulates Jet Plast DP 200 and DP 600, and fused alumina EK 75. All data is on the blasting media page.

What do the figures in the blasting media table mean?

The figure corresponds to the correct nozzle setting in the dosing unit for the respective granulate and surface. The blasting media table lists the values.

How often can the granulate be reused?

According to systeco, up to 100 times in the circuit. This is why systeco says it uses only high-quality granulates.

Is quartz sand allowed as a blasting medium?

No, ordinary quartz sand is not permitted as a blasting medium because the fine dust can cause silicosis (German DGUV Regel 100-500). Vacuum blasting uses the granulates from the systeco overview.

Does systeco offer corundum and glass beads?

systeco offers corundum as fused alumina EK 75 for engraving and roughening natural stone. The blasting glass is crushed glass, not glass beads. Which other granulates come into question for a property is clarified through advice via the contact page.

Which granulate suits sensitive surfaces?

For light, sensitive surfaces such as external insulation, plaster, paint, natural stone and clinker, systeco names the fine blasting glass SG 150; for polished surfaces such as marble and granite, walnut shell NS 450.